Why do espresso shots run faster when I use super fresh coffee? It is a truth universally acknowledged that the gases trapped in fresh coffee create bubbles in espresso, which slows down the flow and reduces extraction. This explains why shots from older coffee run faster, or need a finer grind setting to achieve the same shot time. The bubbles are also often said to inhibit water from contacting the particles properly and hence reduce extraction.
Contradicting this, however, in the SCA Freshness Handbook, Samo Smrke and colleagues reported that freshly roasted coffee actually needs a slightly finer grind to achieve the same shot time, compared to coffee ten days after roasting. After this, the required grind size gets finer again, just like we would expect. Freshly roasted coffee has considerably more gas inside it than coffee that is ten days old, so could be expected to produce more bubbles — but nonetheless the shots run faster!?
To find out what’s going on, we took a close look at how gas bubbles form inside an espresso shot — and come up with some alternative explanations for how coffee freshness affects وقت تحضير الجرعات in espresso.
Are Bubbles Actually Forming Inside the Puck?
Roasted coffee beans contains trapped gases (mainly CO2) inside their cell structure, which are extracted very quickly on contact with hot water. These gases are responsible for the bloom in filter coffee brewing, the crust in a cupping, and the crema of an espresso. The gases are gradually released to the air over time, which explains why older coffee produces less of a bloom, crust, or crema.
While we can clearly see the gas bubbles in crema, it’s less clear whether there are bubbles inside the القُرص during extraction. CO2 is more soluble at higher pressures, so at least some of the gas released will have been dissolved in the high pressure brewing water inside the القُرص.
To establish if the CO2 is dissolving or not, first we need to determine how much there is to be dissolved. The CO2 of freshly roasted coffee varies considerably depending on roast style, with reported values from 8-16mg/g (S Smrke et al., 2017). Immediately after grinding, around half of that is lost (X Wang & L-T Lim, 2014), depending on how finely the coffee is ground. “For espresso [grinds] the loss is much higher, around 80% or even more,” Dr Smrke says.
Lighter roasts may contain even less to start with — the SCA freshness handbook gives a figure of 6-7mg/g for light roasted (filter) coffee, and reports that as much as 75% of this may be lost during grinding. We’ll choose a fairly conservative estimate of 6mg/g for our calculations; that’s a total of 108mg for an 18g shot.
A typical 18g shot might use 70–80ml of water to make an espresso — some of which ends up in the cup, some absorbed in the coffee, and the rest escaping via the exhaust. We’ll assume it all contacts the coffee and therefore the whole volume of water is available to dissolve that CO2.
solubility of CO2 in water depends on temperature and pressure, which vary throughout the القُرص. While there might 9 bars of pressure reaching the top of the القُرص, the coffee when it leaves the basket is back at atmospheric pressure, so there is a gradient of pressure through the القُرص. Similarly, the water hits the coffee at a set temperature, but loses heat to the coffee as it passes through the القُرص.
Under typical brewing conditions in the middle of the القُرص (90°C, 5 bar) 80ml of water will be able to dissolve somewhere around 200mg — comfortably enough to dissolve all the CO2 in the coffee. However, by the time the brew exits the القُرص, at atmospheric pressure the same amount of water at the same temperature can only dissolve about 40mg — so there will be bubbles forming at least for the last part of the water’s journey through the القُرص where the pressure is lower.
Do Bubbles Interfere With Flow?
Whether bubbles can block the pores between coffee particles and thus slow down the flow depends on their size, which in turn depends on the pressure. At 5 bars, in the middle of the القُرص, bubbles would be constrained to be just 0.4μm in diameter, which is small compared to the size of the pores, and so they’re unlikely to have much effect in blocking pores.
Access Our Online Courses
And Premium Content Now!
With a monthly subscription to BH Education, you’ll get access to
12 online courses, 600+ lessons, 200+ videos, powerful apps, online
calculators and lots more, to make online learning easy.
However, at lower pressures, such as you’d find at the start of brewing, or towards the bottom of the القُرص in espresso extractions, the bubbles will be considerably larger. That means there could be bubbles present that are large enough to slow flow for at least part of the time — if only at the very bottom of the القُرص.
Even when the bubbles are small, they do have an overall effect on the viscosity of the liquid — any bubbles dispersed within the liquid will make it more viscous, Dr Smrke says. “[The viscocity] does change based on the bubble size, but it is not easy to estimate the actual effects.”
What Else Might Be Happening?
Based on the above numbers, it looks like the hypothesis of bubbles blocking flow in fresher coffee is plausible, even if it won’t be happening throughout the القُرص but only in a small portion of it, or for a limited time during the early stages of brewing. However, something else must be happening to cause shots to speed up slightly with very fresh coffee.
One possible explanation for Smrke’s et al.’s findings is that the coffee they used may have been sufficiently fresh from the roaster that the beans were still slightly flexible, which would change the way they grind. (If you chew on a bean right out of the roaster, you might notice it’s a little flexible) While the beans in Dr Smrke’s study were ground at least 1h after roasting, it’s possible that the beans were still less brittle than rested beans, he says.
When coffee beans are less brittle, for example when they are heated, they will produce fewer fines when ground, which in turn will make the shot run faster. While many roasters will grind samples for evaluation in a cupping within a few hours of roast, it’s possible that at this point the grind size distribution is still subtly altered — not enough to ruin the cupping, but enough to change the espresso shot time. Unfortunately, the change in distribution required to create the small change in shot time observed will be very small, and therefore very hard to measure.
Dr Smrke has an alternative idea: that the gas is somehow inducing more channeling. “It could be that the gas obstructs the wetting of the bed and favours channeling,” he explains. “We have observed something similar for filter coffee.” He emphasises that this is speculative though, and that proving that this happens for espresso is another matter. “There is as far as I know no good method to determine the magnitude of channeling in a particular extraction.”
Another interesting possibility was suggested to us by Professor Abbott: A super-fresh coffee will have some near-liquid oils on the surface of the particle. Over time, these oils could either evaporate, or soak back into the cellulose matrix of the coffee particles — but in fresh coffee, the surfaces might still be oily.
This thin layer of oil could cause the particles to stick together more tightly, because of capillary binding, which is very strong. Capillary binding is the same process that allows flies to stick to your ceiling (BNJ Persson, 2007) — a thin layer of liquid between two solid surfaces causes them to stick together, pulled together by the surface tension of the liquid, and the adhesion between the liquid and the solid surface.
Because the particles stick together, tamping will not be able to compress the القُرص as much (in technical terms, the القُرص is jamming at a higher void fraction). This creates larger pores for the water to flow through, and thus faster shots or more channeling.
Whatever the mechanism for very fresh coffee making faster espresso shots is, it’s one that most baristas are unlikely to experience in everyday life: the low extraction and ‘gassy’ flavours of too-fresh coffee mean that coffee needs to be rested before being used for espresso, no matter what the effect on shot time and grind size.