Published: Mar 15, 2019

What Effect Does Bed-Depth Have When Increasing Your Dose to Make More Espresso?

Dose is one of the fundamental variables of any brew recipe, yet probably the one that is most often overlooked. Most of us probably tweak the grind size or yield very regularly, but always use the same dose.

In fairness, this is often for a good reason — it makes sense for a cafe to choose a fixed dose, in order to offer consistency in strength and size of drinks. For this reason, at Barista Hustle we recommend choosing a fixed dose that works for your cafe and equipment and sticking to it.

However, the dose you choose definitely has an impact on the flavour and extraction, even if you keep other parameters (such as brew ratio, brew time, or total extraction %) the same.

Choosing a Dose

The most important thing to consider in a cafe setting is how big a drink you want to make. To understand the importance of this, read this classic primer from the archives. That article also explains why you should choose a dose that fits your baskets — or better yet, choose baskets that fit the dose you want to use.

In this post, we’re going to dig deeper, and look in detail at the knock-on effects of that choice, and how it impacts flavour and extraction.

There are three key parameters that the dose will influence: vertical evenness of extraction; grind size; and the risk of channelling. If you’re trying to optimise a dose for flavour, then there’s a major trade-off to make between these three factors.

Vertical Evenness of Extraction

When you brew an espresso, fresh water continually enters the group above the puck, and passes through the coffee bed, picking up coffee solids along the way. By the time the water reaches the lower part of the puck, it’s already loaded with solubles, reducing its extracting power considerably.

This means the coffee at the top of the puck will extract much faster than the coffee at the bottom. The bigger the distance between the top and the bottom, and the more coffee the water has to pass along the way, the bigger that difference in extraction will be.

More even extractions generally taste better, and allow you to use less coffee to get the same strength. So reducing the dose can have a really positive effect both on flavour and your bottom line.

Grind Size and Darcy’s Law

Changing the dose also affects how quickly water flows through your puck. An increased dose presents more resistance to flow, which means a coarser grind size is needed to compensate.

Darcy’s Law is the equation which describes flow through a porous medium (like a coffee bed). Put simply, this law states that the flow rate of liquid through the bed is proportional to the permeability of the bed and inversely proportional to the distance it travels. In other words, if you double your dose, and therefore double the distance the water has to travel, you halve the flow rate.

The permeability in this case is controlled by grind size — grind finer, and the bed becomes less permeable, with a corresponding decrease in flow rate. This explains why, to achieve a given shot time, a lower dose needs a finer grind size.

For espresso, in most cases the finer the grind size, the better the results. Espresso extraction occurs mainly through erosion from the surface of particles (M Petracco, 2005) — there simply isn’t long enough for water to travel into the centre of particles, pick up solubles and diffuse back out. This means a high surface area (a fine grind and/or plenty of ‘fines’) is essential for good extraction in espresso.

A lower dose therefore allows you to grind finer, which can increase extraction and again will most likely improve flavour. However, there is a major limiting factor: channelling.


Most of us experience channelling in espresso, most of the time. Some channels may form only transiently, and some are too small to see, while others can blast right through the puck, giving us the characteristic ‘blonding’ or spray from the basket that baristas are trained to look for. Whether you can see the channels or not, they’re there — and there’s no doubt they make espresso less tasty — by causing areas of localised over-extraction, and resulting in underextraction from the rest of the coffee bed.

A lower bed depth makes it easier for channels to form (M Petracco, 2005). This places a limit on how low a dose can go before the channelling really starts to affect the flavour.

Incidentally, this is the reason some lever machines use narrower baskets, which give you a deeper bed for a given dose. The pressure in some lever machines can reach a peak somewhat higher than 9 bars, which creates an opportunity for channels to form, so the deeper bed counteracts this.

A Side-Note on Preinfusion

The most effective pre-infusion allows the entire bed to become wet before the pressure increases so a bigger dose will benefit from a longer pre-infusion time. If you’re able to adjust your pre-infusion time, try setting it so that the pre-infusion ends just as the first drops start to collect on the underside of your filter basket.

The headspace (the space between the puck and the shower screen) also has an effect here — in a traditional 9 bar espresso machine, a bigger headspace may allow a longer time for the grinds to saturate before full pressure is reached, and this can slightly increase extraction. In a pre-infusion machine on the other hand, a bigger gap means you’ll need extra time to fill the headspace before preinfusion is complete.

So What’s the ‘Ideal’ Dose for Best Flavour?

Assuming that you aren’t restricted by the size of drink you need to make, then adjusting the dose can be a useful tool to tweak the flavour of your shots. Bringing these factors together, we can see that while reducing the dose allows you to grind finer, and makes the extraction more even vertically, it increases the risk of channelling.

So the ideal dose is essentially the lowest you can use before channelling becomes an issue. Where that point lies depends on many things such as your grinder, your technique, and the brew pressure. And since even channels too small to be seen will have a big effect on flavour, the only way to determine the ideal dose is by trial and error, and lots of tasting.


M Petracco, 2005. Percolation. In: A Illy and R Viana (Eds), Espresso Coffee: The Science of Quality, second edition (pp 259-287)


  1. dimitriskapr

    Hi barista hustle again! Happy new year to everyone. I saw the conversation between John buckman and Scott rao last month. At one point of the conversation John spoke about the using lower dose in bigger baskets to increase the heads pace and to increase the extraction. I think he puts 15 gr in a 20 gram basket. My question is who is possible not to have chanelling issues with this? Is the decent machine that helps him? And can we use this in other machines? Thanks again👍

    • BHLearn

      Hi Dimitri, we reached out to John from Decent Espresso and asked him your question. This was his response: ‘I’d recommend that he puts a piece of filter paper on top of the puck if putting a 15g dose in a 20g basket, because the fast flow (and very few holes in group above the puck) from a traditional machine will tend to drill through the puck. The paper will help prevent that drilling.’

  2. dimitriskapr

    Hi again barista hustle. I read the recommended post again but still I can’t understand why the dry dose regulates the size of the drink we make. If I use the same coffee in 2 cafes the first has 18 gr basket so I put 18in 40 out, and the second Cafe has 15 gr basket so I use 15in but again 40out what will happened? why I have to change the yield except the strength what impact it has to taste?

    • BHLearn

      Hi Dimitri. A lot of businesses that have more than one outlet, strive to make the same kind of espresso in all their shops, so that customers moving between outlets have a similar experience in each one. To do this, they usually standardise the basket size and the recipes across all the outlets, often using the same machine and grinder combination too. But if you have a machine with a 55mm group in one shop and a 58mm in another, then in our experience, it’s not going to be possible to produce exactly the same flavour in both places. So in that instance, you’re better off optimising the coffee flavour based on your costing, and what tastes best.

  3. dimitriskapr

    Hi barista hustle. I haven’t exactly understand the topic of choosing the dose by the size of the drink you want to make can you explain it a little be more

Submit a Comment

30 Day Money Back Guarantee+
30 Day Money Back Guarantee

Signup for a personal BH Membership with a 30 day money back guarantee! Signup is risk-free and you can cancel your membership at any time!